No products in the cart.
Shop
Showing 358–378 of 1485 results
RV SeriesEdwards 8 RV8 Rotary Vane Vacuum Pump, Single Phase, 115/230 V, 50/60 Hz, A65401903
All Edwards RV pumps are significantly quieter – noise levels of 48 dBA 50Hz are typically half the noise of a conventional pump and have been achieved by extensive work on the drive train and motor.
The pumps have the unique ability to deliver excellent ultimate vacuum in both high vacuum and high throughput modes with or without gas ballast. This gives the user an unrivalled opportunity to select the optimum pumping performance without compromising the application.
In its high vacuum mode, the Edwards RV8 pump is ideal for analytical instruments, electron microscopes, physics research, backing turbo pumps and leak detection applications. Configure the same pump in the high throughput mode, and it becomes suitable for distillation, laboratory furnaces, backing vapor pumps, solvent concentration, freeze drying and other drying applications.
The simple to use mode selector and accessible, three-position gas ballast control allow the pump to be reconfigured at any time, even when the pump is running.
Edwards RV8 pumps have become the industry standard for scientific primary pumping applications. RV pumps are uniquely capable of delivering high or low throughputs with high ultimate vacuum. This, combined with ultra-low noise levels, makes them ideal for a wide range of applications including GCMS and other small bench top type applications.
Edwards Vacuum RV 5 Rotary Vane Pump Features:
– High reliability – generous lubrication of moving parts.
– Safe process and systems – fast acting inlet valve for best in class anti‑suck back protection.
– Configured to meet your vacuum needs – mode selector and two position gas ballast.
– No unplanned downtime – designed for easy maintenance.
– Better work environment – quiet running and intrusive frequencies minimised.
– Two position gas ballast allows either 60 g/hr or a class leading 220 g/hr (290 g/hr on RV12) of water vapour to be handled.
– Universal motor to cover the widest possible voltage and frequency range from a single variant.
– Smooth controlled inlet valve opening by oil pressure to eliminate pressure surges.
– Rapid closing inlet valve within 0.4 seconds of pump stopping.- AIM series
Edwards AIM S NW 25 Inverted Magnetron Gauge, D14641000
The Edwards AIM Active Inverted Magnetron Gauges (AIM) combine the gauge-head and controller in one compact Active AIM X unit. These gauges have proved to be rugged and reliable in a wide range of applications ranging from scientific instruments to industrial processes.
This gauge has a low external magnetic field making it suitable for use with sensitive analytical instruments or maglev turbo pumps. In addition, this gauge features a linear output for easy integration with a computer or PLC.
Technology
The Edwards AIM-S-NW25 Gauge is an inverted magnetron gauge head and gauge controller in a single compact unit. The gauge operates as a cold cathode ionisation gauge, in which pressure is measured indirectly as a function of the current that flows in a Townsend discharge maintained in the body tube.
The measurement range of the AIM-S-NW25 Gauge is 1 x 10-2 to 1 x 10-8 mbar.
The AIM Gauge requires a 13.5 to 36 V d.c. power supply: it has a 2 to 10 V d.c. analogue output which is related to pressure.
The Edwards AIM-X-NW25 Gauge is compatible with all of Edwards Active Gauge Controllers and with the appropriate versions of the Active Gauge Displays. Alternatively you can use an independent power supply for the AIM Gauge and you can read the AIM Gauge output signal with a voltmeter or an analogue-to-digital converter.
Applications
All vacuum applications requiring rugged and reliable pressure indication in the range 1 x 10-2 to 1 x 10-9 mbar. Typical processes range from general vacuum through industrial coaters and furnaces to scientific instruments and semicon.
- AIM series
Edwards AIM X NW25 Inverted Magnetron Gauge AIM X, D14642000
The Edwards AIM Active Inverted Magnetron Gauges (AIM) combine the gauge-head and controller in one compact Active AIM X unit. These gauges have proved to be rugged and reliable in a wide range of applications ranging from scientific instruments to industrial processes.
This gauge has a low external magnetic field making it suitable for use with sensitive analytical instruments or maglev turbo pumps. In addition, this gauge features a linear output for easy integration with a computer or PLC.
Technology
The Edwards AIM-X-NW25 Gauge is an inverted magnetron gauge head and gauge controller in a single compact unit. The gauge operates as a cold cathode ionisation gauge, in which pressure is measured indirectly as a function of the current that flows in a Townsend discharge maintained in the body tube.
The measurement range of the Edwards AIM-X-NW25 Gauge is 1 x 10-9 to 1 x 10-2 mbar.
The AIM Gauge requires a 13.5 to 36 V d.c. power supply: it has a 2 to 10 V d.c. analogue output which is related to pressure.
The AIM-X-NW25 Gauge is compatible with all of Edwards Active Gauge Controllers and with the appropriate versions of the Active Gauge Displays. Alternatively you can use an independent power supply for the AIM Gauge and you can read the AIM Gauge output signal with a voltmeter or an analogue-to-digital converter.
Applications
All vacuum applications requiring rugged and reliable pressure indication in the range 1 x 10-2 to 1 x 10-9 mbar. Typical processes range from general vacuum through industrial coaters and furnaces to scientific instruments and semicon.
- AIM series
Edwards AIM XL NW25 Inverted Magnetron Gauge, D14645000
The Edwards AIM Active Inverted Magnetron Gauges (AIM) combine the gauge-head and controller in one compact Active AIM XL unit. Low magnetic field version XL for sensitive applications.These gauges have proved to be rugged and reliable in a wide range of applications ranging from scientific instruments to industrial processes.
This gauge has a low external magnetic field making it suitable for use with sensitive analytical instruments or maglev turbo pumps. In addition, this gauge features a linear output for easy integration with a computer or PLC.
Technology
The Edwards AIM-XL-NW25 Gauge is an inverted magnetron gauge head and gauge controller in a single compact unit. The gauge operates as a cold cathode ionisation gauge, in which pressure is measured indirectly as a function of the current that flows in a Townsend discharge maintained in the body tube.
The measurement range of the AIM-XL-NW25 Gauge is 1 x 10-9 to 1 x 10-2 mbar.
The AIM Gauge requires a 13.5 to 36 V d.c. power supply: it has a 2 to 10 V d.c. analogue output which is related to pressure.
The AIM-XL-NW25 Gauge is compatible with all of Edwards Active Gauge Controllers and with the appropriate versions of the Active Gauge Displays. Alternatively you can use an independent power supply for the AIM Gauge and you can read the AIM Gauge output signal with a voltmeter or an analogue-to-digital converter.
Applications
All vacuum applications requiring rugged and reliable pressure indication in the range 1 x 10-2 to 1 x 10-9 mbar. Typical processes range from general vacuum through industrial coaters and furnaces to scientific instruments and semicon.
- APG series
Edwards APG100-XM NW16 Active Pirani Vacuum Gauge with Calibration Certificate, D0260100C
Edwards APG100 series Active Pirani vacuum gaugesare available in 2 models. The
APG100-XM is the standard model and measures to 10-3 mbar. The APG100-XLC is a
corrosion resistant version with measurement to 10-4 mbar.Both Edwards APG100 gauges feature compact size for easy installation, a linear output, and a replaceable
sensor tube. The new gauges are compatible with all Edwards Vacuum TIC instrument
controllers and other active gauge controllers and displays. They are also CSA, C/US
approved as well as fully RoHS compliant due to their lead-free constructionFeatures and Benefits;
Cable connections and gauge adjustment conveniently located, thereby minimizing the space envelope required for access
Sensor tube can be baked to 150 ºC
Adjustable set-point for simple process control and interlocking
Remote calibration possible
Linear output – 1 volt per decade for easy interface with vacuum control systems
NW16 and NW25 flange options for easy connection to vacuum systems – other flange options on request
LED status indicator shows normal and fault conditions - E2M 0.7 and 1.5 series
Edwards E2M0.7 Vacuum Pump, Dual Stage, Rotary Vane Pump, Hydrocarbon Elite Z oil, 200-230 VAC, A37141919
The Edwards Vacuum E2M 0.7 pumps are two-stage, direct drive, sliding vane pumps. The E2M0.7 pump is oil-sealed and designed for reliable, long-term operation. The pump is a free-standing unit. The drive is provided through a coupling by a single-phase motor.
The motor of this rotary vane vacuum pump is totally enclosed and is cooled by the motor-cooling fan which directs air along the motor fins. The motors are fitted with a thermal overload device. When the motor is too hot, the thermal overload device switches off the pump. The thermal overload device has an automatic reset; when the motor cools down, the device resets and the motor will restart.
An oil pressure system lubricates the pump shaft bearing surfaces and rotor sealing faces. The pump has an oil distribution valve which prevents discharge of oil to the pump interior (suckback) after the pump stops. The pumping chambers are air-tight, so this arrangement prevents oil suckback unless the gasballast valve is open.
You can inspect the level and condition of oil in the oil box reservoir through a sight-glass. An oil filler-plug is fitted to the top of the oil box. An oil drain-plug is fitted at the bottom of the oil box. The pump has a carrying handle, inlet-port, outlet nozzle and gas-ballast control. The pump is mounted on a steel baseplate on rubber pads.
Edwards Vacuum E2M 0.7 Features:
– Pumping speeds of either 0.7 to 1.5 m3h‑1.
– Industry proven long term reliable performance.
– Free standing, compact design providing flexibility of use.
– Alternate side inlet connection port so that overall installation height can be reduced to minimum when required.
– Low noise, with the E2M0.7 at just 43 dB(A).
– Low energy consumption, with the E2M0.7 at 0.09 kW.
– O ring sealed sight glass allows visual inspection of oil level and condition.
– Gas ballast valve for large water vapour handling capacity.
– Simple installation and operation with no customer wiring.
– Forced air cooling ensures low pump surface temperature.
– Internal ATEX classification of Ex II 3 G c IIB T4.
– Approved EN61010, CSA22.2 and UL61010. - E2M 0.7 and 1.5 series
Edwards E2M1.5 Vacuum Pump, Dual Stage, Rotary Vane Pump, Hydrocarbon Elite Z oil, 200-230 VAC, IEC Connector, A37132919
The Edwards Vacuum E2M 1.5 pumps are two-stage, direct drive, sliding vane pumps. The E2M1.5 pump is oil-sealed and designed for reliable, long-term operation. The pump is a free-standing unit. The drive is provided through a coupling by a single-phase motor.
The motor of this rotary vane vacuum pump is totally enclosed and is cooled by the motor-cooling fan which directs air along the motor fins. The motors are fitted with a thermal overload device. When the motor is too hot, the thermal overload device switches off the pump. The thermal overload device has an automatic reset; when the motor cools down, the device resets and the motor will restart.
An oil pressure system lubricates the pump shaft bearing surfaces and rotor sealing faces. The pump has an oil distribution valve which prevents discharge of oil to the pump interior (suckback) after the pump stops. The pumping chambers are air-tight, so this arrangement prevents oil suckback unless the gasballast valve is open.
You can inspect the level and condition of oil in the oil box reservoir through a sight-glass. An oil filler-plug is fitted to the top of the oil box. An oil drain-plug is fitted at the bottom of the oil box. The pump has a carrying handle, inlet-port, outlet nozzle and gas-ballast control. The pump is mounted on a steel baseplate on rubber pads.
Edwards Vacuum E2M 1.5 Features:
– Pumping speeds of either 0.7 to 1.5 m3h‑1.
– Industry proven long term reliable performance.
– Free standing, compact design providing flexibility of use.
– Alternate side inlet connection port so that overall installation height can be reduced to minimum when required.
– Low noise, with the E2M0.7 at just 43 dB(A).
– Low energy consumption, with the E2M0.7 at 0.09 kW.
– O ring sealed sight glass allows visual inspection of oil level and condition.
– Gas ballast valve for large water vapour handling capacity.
– Simple installation and operation with no customer wiring.
– Forced air cooling ensures low pump surface temperature.
– Internal ATEX classification of Ex II 3 G c IIB T4.
– Approved EN61010, CSA22.2 and UL61010. - E2M 18 and 28 series
Edwards E2M18 Dual Stage Rotary Vane Pump, Single Phase, 115/200-230 V, 50/60 Hz, A36317984
The Edwards E2M18 Rotary Vane Pump is a vacuum pump that has a pressurized oil system that lubricates the pump shaft bearing surfaces and rotor sealing faces. The pump has an oil distribution valve which prevents discharge of oil to the pump interior (suckback) after the pump stops. The pumping chambers are air-tight, so this arrangement prevents oil suckback unless the gas ballast valve is open.
You can inspect the level and condition of oil in the oil box reservoir through the oil sight-glass. An oil filler-plug is fitted to the top of the oil box. The pump has an oil drain-plug to allow either gravity oil drain or pressure oil drain.
The EM Vacuum Pump Series range of oil‑sealed rotary pumps – renowned for their high ultimate vacuum, rapid pumping speed, quiet operation and ability to handle vapour – have become the industry standard for laboratory and light industrial applications. The pump is a freestanding unit with the drive provided through a flexible coupling by either a single‑phase or three‑phase (four pole) motor.
Edwards E2M 18 Dual Stage Rotary Vane Pump Features:
– The pump is designed for reliable, long‑term operation.
– Thermal overload device prevents overheating (single phase only).
– The drive is provided through a flexible coupling by a single‑phase or three‑phase (four pole) motor.
– The motors are totally enclosed and are cooled by the motor cooling fan.
– Full height O ring sealed oil sight glass for easy checking of oil level and condition.
– Large sight glass and operating oil range.
– IE3 energy efficient 3 phase motor used with E2M28. - E2M 18 and 28 series
Edwards E2M18 Dual Stage Rotary Vane Pump, Three Phase, 200-230/380-415 V, 50 Hz or 200-230/460 V, 60 Hz, A36310940
The Edwards E2M18 Rotary Vane Pump is a vacuum pump that has a pressurized oil system that lubricates the pump shaft bearing surfaces and rotor sealing faces. The pump has an oil distribution valve which prevents discharge of oil to the pump interior (suckback) after the pump stops. The pumping chambers are air-tight, so this arrangement prevents oil suckback unless the gas ballast valve is open.
You can inspect the level and condition of oil in the oil box reservoir through the oil sight-glass. An oil filler-plug is fitted to the top of the oil box. The pump has an oil drain-plug to allow either gravity oil drain or pressure oil drain.
The EM Vacuum Pump Series range of oil‑sealed rotary pumps – renowned for their high ultimate vacuum, rapid pumping speed, quiet operation and ability to handle vapour – have become the industry standard for laboratory and light industrial applications. The pump is a freestanding unit with the drive provided through a flexible coupling by either a single‑phase or three‑phase (four pole) motor.
Edwards E2M 18 Dual Stage Rotary Vane Pump Features:
– The pump is designed for reliable, long‑term operation.
– Thermal overload device prevents overheating (single phase only).
– The drive is provided through a flexible coupling by a single‑phase or three‑phase (four pole) motor.
– The motors are totally enclosed and are cooled by the motor cooling fan.
– Full height O ring sealed oil sight glass for easy checking of oil level and condition.
– Large sight glass and operating oil range.
– IE3 energy efficient 3 phase motor used with E2M28. - E2M 18 and 28 series
Edwards E2M28 Dual Stage Rotary Vane Pump, Single Phase, 115/200-230 V, 50/60 Hz, A37317984
The E2M28 Rotary Vane Pump is a two-stage, direct drive, sliding vane pump. The pump is oil-sealed and designed for reliable, long-term operation in both laboratory and industrial environments. The pump is a free-standing unit. The drive is provided through a flexible coupling by a single-phase or three-phase (four pole) motor.
The motors are totally enclosed and are cooled by the motor-cooling fan which directs air along the motor fins.
The single-phase motors have a thermal overload device. When the motor is too hot, the thermal overload device switches off the pump. The thermal overload device has an automatic reset; when the motor cools down, the device resets and the motor will restart. The single phase motors have an on/off switch.
An oil pressure system lubricates the pump shaft bearing surfaces and rotor sealing faces. The pump has an oil distribution valve which prevents discharge of oil to the pump interior (suckback) after the pump stops. The pumping chambers are air-tight, so this arrangement prevents air suckback unless the gas-ballast valve is open.
You can inspect the level and condition of oil in the oil box reservoir through the oil sight-glass. An oil filler-plug is fitted to the top of the oil box. The pump has an oil drain-plug to allow gravity oil drain.
The pump has an inlet-port, outlet nozzle and gas-ballast control. The pump is mounted on an aluminum alloy baseplate on rubber pads.
Edwards E2M28 Rotary Vane Vacuum Pump Features:
– The pump is designed for reliable, long‑term operation.
– Thermal overload device prevents overheating (single phase only).
– The drive is provided through a flexible coupling by a single‑phase or three‑phase (four pole) motor.
– The motors are totally enclosed and are cooled by the motor cooling fan.
– Full height O ring sealed oil sight glass for easy checking of oil level and condition.
– Large sight glass and operating oil range.
– IE3 energy efficient 3 phase motor used with E2M28. - E2M 18 and 28 series
Edwards E2M28 Rotary Vane Vacuum Pump, Hydrocarbon Oil, Dual Stage, 200-220/380-415 V, Three Phase, 50Hz, A37310940
The E2M28 Rotary Vane Pump is a two-stage, direct drive, sliding vane pump. The pump is oil-sealed and designed for reliable, long-term operation in both laboratory and industrial environments. The pump is a free-standing unit. The drive is provided through a flexible coupling by a single-phase or three-phase (four pole) motor.
The motors are totally enclosed and are cooled by the motor-cooling fan which directs air along the motor fins.
The single-phase motors have a thermal overload device. When the motor is too hot, the thermal overload device switches off the pump. The thermal overload device has an automatic reset; when the motor cools down, the device resets and the motor will restart. The single phase motors have an on/off switch.
An oil pressure system lubricates the pump shaft bearing surfaces and rotor sealing faces. The pump has an oil distribution valve which prevents discharge of oil to the pump interior (suckback) after the pump stops. The pumping chambers are air-tight, so this arrangement prevents air suckback unless the gas-ballast valve is open.
You can inspect the level and condition of oil in the oil box reservoir through the oil sight-glass. An oil filler-plug is fitted to the top of the oil box. The pump has an oil drain-plug to allow gravity oil drain.
The pump has an inlet-port, outlet nozzle and gas-ballast control. The pump is mounted on an aluminum alloy baseplate on rubber pads.
Edwards E2M28 Rotary Vane Vacuum Pump Features:
– The pump is designed for reliable, long‑term operation.
– Thermal overload device prevents overheating (single phase only).
– The drive is provided through a flexible coupling by a single‑phase or three‑phase (four pole) motor.
– The motors are totally enclosed and are cooled by the motor cooling fan.
– Full height O ring sealed oil sight glass for easy checking of oil level and condition.
– Large sight glass and operating oil range.
– IE3 energy efficient 3 phase motor used with E2M28. - New Turbo Pump Controllers
Edwards EXDC80 Turbo Pump Controller, 24V, 93W, D39645000
The Edwards EXDC80 Turbo Pump Controller generates the control signals necessary to operate an EXT pump and its accessories.
The EXDC has no manual controls and can only be operated through the logic interface. To operate the EXT pump, you must therefore connect the EXDC to your own control equipment and electrical supply.
This Controller is designed for the following Mass Spectrometer Turbo Pumps:
- Edwards EXT 70 Turbo Pump
- Edwards EXT 70H Turbo Pump
- Edwards EXT 250 Turbo Pump
- Edwards EXT 255H Turbo Pump
- RV Series
Edwards 8 RV8 Rotary Vane Vacuum Pump, Single Phase, 115/230 V, 50/60 Hz, A65401903
All Edwards RV pumps are significantly quieter – noise levels of 48 dBA 50Hz are typically half the noise of a conventional pump and have been achieved by extensive work on the drive train and motor.
The pumps have the unique ability to deliver excellent ultimate vacuum in both high vacuum and high throughput modes with or without gas ballast. This gives the user an unrivalled opportunity to select the optimum pumping performance without compromising the application.
In its high vacuum mode, the Edwards RV8 pump is ideal for analytical instruments, electron microscopes, physics research, backing turbo pumps and leak detection applications. Configure the same pump in the high throughput mode, and it becomes suitable for distillation, laboratory furnaces, backing vapor pumps, solvent concentration, freeze drying and other drying applications.
The simple to use mode selector and accessible, three-position gas ballast control allow the pump to be reconfigured at any time, even when the pump is running.
Edwards RV8 pumps have become the industry standard for scientific primary pumping applications. RV pumps are uniquely capable of delivering high or low throughputs with high ultimate vacuum. This, combined with ultra-low noise levels, makes them ideal for a wide range of applications including GCMS and other small bench top type applications.
Edwards Vacuum RV 5 Rotary Vane Pump Features:
– High reliability – generous lubrication of moving parts.
– Safe process and systems – fast acting inlet valve for best in class anti‑suck back protection.
– Configured to meet your vacuum needs – mode selector and two position gas ballast.
– No unplanned downtime – designed for easy maintenance.
– Better work environment – quiet running and intrusive frequencies minimised.
– Two position gas ballast allows either 60 g/hr or a class leading 220 g/hr (290 g/hr on RV12) of water vapour to be handled.
– Universal motor to cover the widest possible voltage and frequency range from a single variant.
– Smooth controlled inlet valve opening by oil pressure to eliminate pressure surges.
– Rapid closing inlet valve within 0.4 seconds of pump stopping.SKU: A65401903Login to see price! Add to cart - AIM series
Edwards AIM S NW 25 Inverted Magnetron Gauge, D14641000
The Edwards AIM Active Inverted Magnetron Gauges (AIM) combine the gauge-head and controller in one compact Active AIM X unit. These gauges have proved to be rugged and reliable in a wide range of applications ranging from scientific instruments to industrial processes.
This gauge has a low external magnetic field making it suitable for use with sensitive analytical instruments or maglev turbo pumps. In addition, this gauge features a linear output for easy integration with a computer or PLC.
Technology
The Edwards AIM-S-NW25 Gauge is an inverted magnetron gauge head and gauge controller in a single compact unit. The gauge operates as a cold cathode ionisation gauge, in which pressure is measured indirectly as a function of the current that flows in a Townsend discharge maintained in the body tube.
The measurement range of the AIM-S-NW25 Gauge is 1 x 10-2 to 1 x 10-8 mbar.
The AIM Gauge requires a 13.5 to 36 V d.c. power supply: it has a 2 to 10 V d.c. analogue output which is related to pressure.
The Edwards AIM-X-NW25 Gauge is compatible with all of Edwards Active Gauge Controllers and with the appropriate versions of the Active Gauge Displays. Alternatively you can use an independent power supply for the AIM Gauge and you can read the AIM Gauge output signal with a voltmeter or an analogue-to-digital converter.
Applications
All vacuum applications requiring rugged and reliable pressure indication in the range 1 x 10-2 to 1 x 10-9 mbar. Typical processes range from general vacuum through industrial coaters and furnaces to scientific instruments and semicon.
SKU: n/aLogin to see price! Add to cart - AIM series
Edwards AIM X NW25 Inverted Magnetron Gauge AIM X, D14642000
The Edwards AIM Active Inverted Magnetron Gauges (AIM) combine the gauge-head and controller in one compact Active AIM X unit. These gauges have proved to be rugged and reliable in a wide range of applications ranging from scientific instruments to industrial processes.
This gauge has a low external magnetic field making it suitable for use with sensitive analytical instruments or maglev turbo pumps. In addition, this gauge features a linear output for easy integration with a computer or PLC.
Technology
The Edwards AIM-X-NW25 Gauge is an inverted magnetron gauge head and gauge controller in a single compact unit. The gauge operates as a cold cathode ionisation gauge, in which pressure is measured indirectly as a function of the current that flows in a Townsend discharge maintained in the body tube.
The measurement range of the Edwards AIM-X-NW25 Gauge is 1 x 10-9 to 1 x 10-2 mbar.
The AIM Gauge requires a 13.5 to 36 V d.c. power supply: it has a 2 to 10 V d.c. analogue output which is related to pressure.
The AIM-X-NW25 Gauge is compatible with all of Edwards Active Gauge Controllers and with the appropriate versions of the Active Gauge Displays. Alternatively you can use an independent power supply for the AIM Gauge and you can read the AIM Gauge output signal with a voltmeter or an analogue-to-digital converter.
Applications
All vacuum applications requiring rugged and reliable pressure indication in the range 1 x 10-2 to 1 x 10-9 mbar. Typical processes range from general vacuum through industrial coaters and furnaces to scientific instruments and semicon.
SKU: n/aLogin to see price! Add to cart - AIM series
Edwards AIM XL NW25 Inverted Magnetron Gauge, D14645000
The Edwards AIM Active Inverted Magnetron Gauges (AIM) combine the gauge-head and controller in one compact Active AIM XL unit. Low magnetic field version XL for sensitive applications.These gauges have proved to be rugged and reliable in a wide range of applications ranging from scientific instruments to industrial processes.
This gauge has a low external magnetic field making it suitable for use with sensitive analytical instruments or maglev turbo pumps. In addition, this gauge features a linear output for easy integration with a computer or PLC.
Technology
The Edwards AIM-XL-NW25 Gauge is an inverted magnetron gauge head and gauge controller in a single compact unit. The gauge operates as a cold cathode ionisation gauge, in which pressure is measured indirectly as a function of the current that flows in a Townsend discharge maintained in the body tube.
The measurement range of the AIM-XL-NW25 Gauge is 1 x 10-9 to 1 x 10-2 mbar.
The AIM Gauge requires a 13.5 to 36 V d.c. power supply: it has a 2 to 10 V d.c. analogue output which is related to pressure.
The AIM-XL-NW25 Gauge is compatible with all of Edwards Active Gauge Controllers and with the appropriate versions of the Active Gauge Displays. Alternatively you can use an independent power supply for the AIM Gauge and you can read the AIM Gauge output signal with a voltmeter or an analogue-to-digital converter.
Applications
All vacuum applications requiring rugged and reliable pressure indication in the range 1 x 10-2 to 1 x 10-9 mbar. Typical processes range from general vacuum through industrial coaters and furnaces to scientific instruments and semicon.
SKU: n/aLogin to see price! Add to cart - APG series
Edwards APG100-XM NW16 Active Pirani Vacuum Gauge with Calibration Certificate, D0260100C
Edwards APG100 series Active Pirani vacuum gaugesare available in 2 models. The
APG100-XM is the standard model and measures to 10-3 mbar. The APG100-XLC is a
corrosion resistant version with measurement to 10-4 mbar.Both Edwards APG100 gauges feature compact size for easy installation, a linear output, and a replaceable
sensor tube. The new gauges are compatible with all Edwards Vacuum TIC instrument
controllers and other active gauge controllers and displays. They are also CSA, C/US
approved as well as fully RoHS compliant due to their lead-free constructionFeatures and Benefits;
Cable connections and gauge adjustment conveniently located, thereby minimizing the space envelope required for access
Sensor tube can be baked to 150 ºC
Adjustable set-point for simple process control and interlocking
Remote calibration possible
Linear output – 1 volt per decade for easy interface with vacuum control systems
NW16 and NW25 flange options for easy connection to vacuum systems – other flange options on request
LED status indicator shows normal and fault conditionsSKU: D0260100CLogin to see price! Add to cart - E2M 0.7 and 1.5 series
Edwards E2M0.7 Vacuum Pump, Dual Stage, Rotary Vane Pump, Hydrocarbon Elite Z oil, 200-230 VAC, A37141919
The Edwards Vacuum E2M 0.7 pumps are two-stage, direct drive, sliding vane pumps. The E2M0.7 pump is oil-sealed and designed for reliable, long-term operation. The pump is a free-standing unit. The drive is provided through a coupling by a single-phase motor.
The motor of this rotary vane vacuum pump is totally enclosed and is cooled by the motor-cooling fan which directs air along the motor fins. The motors are fitted with a thermal overload device. When the motor is too hot, the thermal overload device switches off the pump. The thermal overload device has an automatic reset; when the motor cools down, the device resets and the motor will restart.
An oil pressure system lubricates the pump shaft bearing surfaces and rotor sealing faces. The pump has an oil distribution valve which prevents discharge of oil to the pump interior (suckback) after the pump stops. The pumping chambers are air-tight, so this arrangement prevents oil suckback unless the gasballast valve is open.
You can inspect the level and condition of oil in the oil box reservoir through a sight-glass. An oil filler-plug is fitted to the top of the oil box. An oil drain-plug is fitted at the bottom of the oil box. The pump has a carrying handle, inlet-port, outlet nozzle and gas-ballast control. The pump is mounted on a steel baseplate on rubber pads.
Edwards Vacuum E2M 0.7 Features:
– Pumping speeds of either 0.7 to 1.5 m3h‑1.
– Industry proven long term reliable performance.
– Free standing, compact design providing flexibility of use.
– Alternate side inlet connection port so that overall installation height can be reduced to minimum when required.
– Low noise, with the E2M0.7 at just 43 dB(A).
– Low energy consumption, with the E2M0.7 at 0.09 kW.
– O ring sealed sight glass allows visual inspection of oil level and condition.
– Gas ballast valve for large water vapour handling capacity.
– Simple installation and operation with no customer wiring.
– Forced air cooling ensures low pump surface temperature.
– Internal ATEX classification of Ex II 3 G c IIB T4.
– Approved EN61010, CSA22.2 and UL61010.SKU: A37141919Login to see price! Add to cart - E2M 0.7 and 1.5 series
Edwards E2M1.5 Vacuum Pump, Dual Stage, Rotary Vane Pump, Hydrocarbon Elite Z oil, 200-230 VAC, IEC Connector, A37132919
The Edwards Vacuum E2M 1.5 pumps are two-stage, direct drive, sliding vane pumps. The E2M1.5 pump is oil-sealed and designed for reliable, long-term operation. The pump is a free-standing unit. The drive is provided through a coupling by a single-phase motor.
The motor of this rotary vane vacuum pump is totally enclosed and is cooled by the motor-cooling fan which directs air along the motor fins. The motors are fitted with a thermal overload device. When the motor is too hot, the thermal overload device switches off the pump. The thermal overload device has an automatic reset; when the motor cools down, the device resets and the motor will restart.
An oil pressure system lubricates the pump shaft bearing surfaces and rotor sealing faces. The pump has an oil distribution valve which prevents discharge of oil to the pump interior (suckback) after the pump stops. The pumping chambers are air-tight, so this arrangement prevents oil suckback unless the gasballast valve is open.
You can inspect the level and condition of oil in the oil box reservoir through a sight-glass. An oil filler-plug is fitted to the top of the oil box. An oil drain-plug is fitted at the bottom of the oil box. The pump has a carrying handle, inlet-port, outlet nozzle and gas-ballast control. The pump is mounted on a steel baseplate on rubber pads.
Edwards Vacuum E2M 1.5 Features:
– Pumping speeds of either 0.7 to 1.5 m3h‑1.
– Industry proven long term reliable performance.
– Free standing, compact design providing flexibility of use.
– Alternate side inlet connection port so that overall installation height can be reduced to minimum when required.
– Low noise, with the E2M0.7 at just 43 dB(A).
– Low energy consumption, with the E2M0.7 at 0.09 kW.
– O ring sealed sight glass allows visual inspection of oil level and condition.
– Gas ballast valve for large water vapour handling capacity.
– Simple installation and operation with no customer wiring.
– Forced air cooling ensures low pump surface temperature.
– Internal ATEX classification of Ex II 3 G c IIB T4.
– Approved EN61010, CSA22.2 and UL61010.SKU: A37132919Login to see price! Add to cart - E2M 18 and 28 series
Edwards E2M18 Dual Stage Rotary Vane Pump, Single Phase, 115/200-230 V, 50/60 Hz, A36317984
The Edwards E2M18 Rotary Vane Pump is a vacuum pump that has a pressurized oil system that lubricates the pump shaft bearing surfaces and rotor sealing faces. The pump has an oil distribution valve which prevents discharge of oil to the pump interior (suckback) after the pump stops. The pumping chambers are air-tight, so this arrangement prevents oil suckback unless the gas ballast valve is open.
You can inspect the level and condition of oil in the oil box reservoir through the oil sight-glass. An oil filler-plug is fitted to the top of the oil box. The pump has an oil drain-plug to allow either gravity oil drain or pressure oil drain.
The EM Vacuum Pump Series range of oil‑sealed rotary pumps – renowned for their high ultimate vacuum, rapid pumping speed, quiet operation and ability to handle vapour – have become the industry standard for laboratory and light industrial applications. The pump is a freestanding unit with the drive provided through a flexible coupling by either a single‑phase or three‑phase (four pole) motor.
Edwards E2M 18 Dual Stage Rotary Vane Pump Features:
– The pump is designed for reliable, long‑term operation.
– Thermal overload device prevents overheating (single phase only).
– The drive is provided through a flexible coupling by a single‑phase or three‑phase (four pole) motor.
– The motors are totally enclosed and are cooled by the motor cooling fan.
– Full height O ring sealed oil sight glass for easy checking of oil level and condition.
– Large sight glass and operating oil range.
– IE3 energy efficient 3 phase motor used with E2M28.SKU: A36317984Login to see price! Add to cart - E2M 18 and 28 series
Edwards E2M18 Dual Stage Rotary Vane Pump, Three Phase, 200-230/380-415 V, 50 Hz or 200-230/460 V, 60 Hz, A36310940
The Edwards E2M18 Rotary Vane Pump is a vacuum pump that has a pressurized oil system that lubricates the pump shaft bearing surfaces and rotor sealing faces. The pump has an oil distribution valve which prevents discharge of oil to the pump interior (suckback) after the pump stops. The pumping chambers are air-tight, so this arrangement prevents oil suckback unless the gas ballast valve is open.
You can inspect the level and condition of oil in the oil box reservoir through the oil sight-glass. An oil filler-plug is fitted to the top of the oil box. The pump has an oil drain-plug to allow either gravity oil drain or pressure oil drain.
The EM Vacuum Pump Series range of oil‑sealed rotary pumps – renowned for their high ultimate vacuum, rapid pumping speed, quiet operation and ability to handle vapour – have become the industry standard for laboratory and light industrial applications. The pump is a freestanding unit with the drive provided through a flexible coupling by either a single‑phase or three‑phase (four pole) motor.
Edwards E2M 18 Dual Stage Rotary Vane Pump Features:
– The pump is designed for reliable, long‑term operation.
– Thermal overload device prevents overheating (single phase only).
– The drive is provided through a flexible coupling by a single‑phase or three‑phase (four pole) motor.
– The motors are totally enclosed and are cooled by the motor cooling fan.
– Full height O ring sealed oil sight glass for easy checking of oil level and condition.
– Large sight glass and operating oil range.
– IE3 energy efficient 3 phase motor used with E2M28.SKU: A36310940Login to see price! Add to cart - E2M 18 and 28 series
Edwards E2M28 Dual Stage Rotary Vane Pump, Single Phase, 115/200-230 V, 50/60 Hz, A37317984
The E2M28 Rotary Vane Pump is a two-stage, direct drive, sliding vane pump. The pump is oil-sealed and designed for reliable, long-term operation in both laboratory and industrial environments. The pump is a free-standing unit. The drive is provided through a flexible coupling by a single-phase or three-phase (four pole) motor.
The motors are totally enclosed and are cooled by the motor-cooling fan which directs air along the motor fins.
The single-phase motors have a thermal overload device. When the motor is too hot, the thermal overload device switches off the pump. The thermal overload device has an automatic reset; when the motor cools down, the device resets and the motor will restart. The single phase motors have an on/off switch.
An oil pressure system lubricates the pump shaft bearing surfaces and rotor sealing faces. The pump has an oil distribution valve which prevents discharge of oil to the pump interior (suckback) after the pump stops. The pumping chambers are air-tight, so this arrangement prevents air suckback unless the gas-ballast valve is open.
You can inspect the level and condition of oil in the oil box reservoir through the oil sight-glass. An oil filler-plug is fitted to the top of the oil box. The pump has an oil drain-plug to allow gravity oil drain.
The pump has an inlet-port, outlet nozzle and gas-ballast control. The pump is mounted on an aluminum alloy baseplate on rubber pads.
Edwards E2M28 Rotary Vane Vacuum Pump Features:
– The pump is designed for reliable, long‑term operation.
– Thermal overload device prevents overheating (single phase only).
– The drive is provided through a flexible coupling by a single‑phase or three‑phase (four pole) motor.
– The motors are totally enclosed and are cooled by the motor cooling fan.
– Full height O ring sealed oil sight glass for easy checking of oil level and condition.
– Large sight glass and operating oil range.
– IE3 energy efficient 3 phase motor used with E2M28.SKU: A37317984Login to see price! Add to cart - E2M 18 and 28 series
Edwards E2M28 Rotary Vane Vacuum Pump, Hydrocarbon Oil, Dual Stage, 200-220/380-415 V, Three Phase, 50Hz, A37310940
The E2M28 Rotary Vane Pump is a two-stage, direct drive, sliding vane pump. The pump is oil-sealed and designed for reliable, long-term operation in both laboratory and industrial environments. The pump is a free-standing unit. The drive is provided through a flexible coupling by a single-phase or three-phase (four pole) motor.
The motors are totally enclosed and are cooled by the motor-cooling fan which directs air along the motor fins.
The single-phase motors have a thermal overload device. When the motor is too hot, the thermal overload device switches off the pump. The thermal overload device has an automatic reset; when the motor cools down, the device resets and the motor will restart. The single phase motors have an on/off switch.
An oil pressure system lubricates the pump shaft bearing surfaces and rotor sealing faces. The pump has an oil distribution valve which prevents discharge of oil to the pump interior (suckback) after the pump stops. The pumping chambers are air-tight, so this arrangement prevents air suckback unless the gas-ballast valve is open.
You can inspect the level and condition of oil in the oil box reservoir through the oil sight-glass. An oil filler-plug is fitted to the top of the oil box. The pump has an oil drain-plug to allow gravity oil drain.
The pump has an inlet-port, outlet nozzle and gas-ballast control. The pump is mounted on an aluminum alloy baseplate on rubber pads.
Edwards E2M28 Rotary Vane Vacuum Pump Features:
– The pump is designed for reliable, long‑term operation.
– Thermal overload device prevents overheating (single phase only).
– The drive is provided through a flexible coupling by a single‑phase or three‑phase (four pole) motor.
– The motors are totally enclosed and are cooled by the motor cooling fan.
– Full height O ring sealed oil sight glass for easy checking of oil level and condition.
– Large sight glass and operating oil range.
– IE3 energy efficient 3 phase motor used with E2M28.SKU: A37310940Login to see price! Add to cart - New Turbo Pump Controllers
Edwards EXDC80 Turbo Pump Controller, 24V, 93W, D39645000
The Edwards EXDC80 Turbo Pump Controller generates the control signals necessary to operate an EXT pump and its accessories.
The EXDC has no manual controls and can only be operated through the logic interface. To operate the EXT pump, you must therefore connect the EXDC to your own control equipment and electrical supply.
This Controller is designed for the following Mass Spectrometer Turbo Pumps:
- Edwards EXT 70 Turbo Pump
- Edwards EXT 70H Turbo Pump
- Edwards EXT 250 Turbo Pump
- Edwards EXT 255H Turbo Pump
SKU: D39645000Login to see price! Add to cart
- RV Series
Edwards 8 RV8 Rotary Vane Vacuum Pump, Single Phase, 115/230 V, 50/60 Hz, A65401903
All Edwards RV pumps are significantly quieter – noise levels of 48 dBA 50Hz are typically half the noise of a conventional pump and have been achieved by extensive work on the drive train and motor.
The pumps have the unique ability to deliver excellent ultimate vacuum in both high vacuum and high throughput modes with or without gas ballast. This gives the user an unrivalled opportunity to select the optimum pumping performance without compromising the application.
In its high vacuum mode, the Edwards RV8 pump is ideal for analytical instruments, electron microscopes, physics research, backing turbo pumps and leak detection applications. Configure the same pump in the high throughput mode, and it becomes suitable for distillation, laboratory furnaces, backing vapor pumps, solvent concentration, freeze drying and other drying applications.
The simple to use mode selector and accessible, three-position gas ballast control allow the pump to be reconfigured at any time, even when the pump is running.
Edwards RV8 pumps have become the industry standard for scientific primary pumping applications. RV pumps are uniquely capable of delivering high or low throughputs with high ultimate vacuum. This, combined with ultra-low noise levels, makes them ideal for a wide range of applications including GCMS and other small bench top type applications.
Edwards Vacuum RV 5 Rotary Vane Pump Features:
– High reliability – generous lubrication of moving parts.
– Safe process and systems – fast acting inlet valve for best in class anti‑suck back protection.
– Configured to meet your vacuum needs – mode selector and two position gas ballast.
– No unplanned downtime – designed for easy maintenance.
– Better work environment – quiet running and intrusive frequencies minimised.
– Two position gas ballast allows either 60 g/hr or a class leading 220 g/hr (290 g/hr on RV12) of water vapour to be handled.
– Universal motor to cover the widest possible voltage and frequency range from a single variant.
– Smooth controlled inlet valve opening by oil pressure to eliminate pressure surges.
– Rapid closing inlet valve within 0.4 seconds of pump stopping.Login to see price! Add to cart - AIM series
Edwards AIM S NW 25 Inverted Magnetron Gauge, D14641000
The Edwards AIM Active Inverted Magnetron Gauges (AIM) combine the gauge-head and controller in one compact Active AIM X unit. These gauges have proved to be rugged and reliable in a wide range of applications ranging from scientific instruments to industrial processes.
This gauge has a low external magnetic field making it suitable for use with sensitive analytical instruments or maglev turbo pumps. In addition, this gauge features a linear output for easy integration with a computer or PLC.
Technology
The Edwards AIM-S-NW25 Gauge is an inverted magnetron gauge head and gauge controller in a single compact unit. The gauge operates as a cold cathode ionisation gauge, in which pressure is measured indirectly as a function of the current that flows in a Townsend discharge maintained in the body tube.
The measurement range of the AIM-S-NW25 Gauge is 1 x 10-2 to 1 x 10-8 mbar.
The AIM Gauge requires a 13.5 to 36 V d.c. power supply: it has a 2 to 10 V d.c. analogue output which is related to pressure.
The Edwards AIM-X-NW25 Gauge is compatible with all of Edwards Active Gauge Controllers and with the appropriate versions of the Active Gauge Displays. Alternatively you can use an independent power supply for the AIM Gauge and you can read the AIM Gauge output signal with a voltmeter or an analogue-to-digital converter.
Applications
All vacuum applications requiring rugged and reliable pressure indication in the range 1 x 10-2 to 1 x 10-9 mbar. Typical processes range from general vacuum through industrial coaters and furnaces to scientific instruments and semicon.
Login to see price! Add to cart - AIM series
Edwards AIM X NW25 Inverted Magnetron Gauge AIM X, D14642000
The Edwards AIM Active Inverted Magnetron Gauges (AIM) combine the gauge-head and controller in one compact Active AIM X unit. These gauges have proved to be rugged and reliable in a wide range of applications ranging from scientific instruments to industrial processes.
This gauge has a low external magnetic field making it suitable for use with sensitive analytical instruments or maglev turbo pumps. In addition, this gauge features a linear output for easy integration with a computer or PLC.
Technology
The Edwards AIM-X-NW25 Gauge is an inverted magnetron gauge head and gauge controller in a single compact unit. The gauge operates as a cold cathode ionisation gauge, in which pressure is measured indirectly as a function of the current that flows in a Townsend discharge maintained in the body tube.
The measurement range of the Edwards AIM-X-NW25 Gauge is 1 x 10-9 to 1 x 10-2 mbar.
The AIM Gauge requires a 13.5 to 36 V d.c. power supply: it has a 2 to 10 V d.c. analogue output which is related to pressure.
The AIM-X-NW25 Gauge is compatible with all of Edwards Active Gauge Controllers and with the appropriate versions of the Active Gauge Displays. Alternatively you can use an independent power supply for the AIM Gauge and you can read the AIM Gauge output signal with a voltmeter or an analogue-to-digital converter.
Applications
All vacuum applications requiring rugged and reliable pressure indication in the range 1 x 10-2 to 1 x 10-9 mbar. Typical processes range from general vacuum through industrial coaters and furnaces to scientific instruments and semicon.
Login to see price! Add to cart - AIM series
Edwards AIM XL NW25 Inverted Magnetron Gauge, D14645000
The Edwards AIM Active Inverted Magnetron Gauges (AIM) combine the gauge-head and controller in one compact Active AIM XL unit. Low magnetic field version XL for sensitive applications.These gauges have proved to be rugged and reliable in a wide range of applications ranging from scientific instruments to industrial processes.
This gauge has a low external magnetic field making it suitable for use with sensitive analytical instruments or maglev turbo pumps. In addition, this gauge features a linear output for easy integration with a computer or PLC.
Technology
The Edwards AIM-XL-NW25 Gauge is an inverted magnetron gauge head and gauge controller in a single compact unit. The gauge operates as a cold cathode ionisation gauge, in which pressure is measured indirectly as a function of the current that flows in a Townsend discharge maintained in the body tube.
The measurement range of the AIM-XL-NW25 Gauge is 1 x 10-9 to 1 x 10-2 mbar.
The AIM Gauge requires a 13.5 to 36 V d.c. power supply: it has a 2 to 10 V d.c. analogue output which is related to pressure.
The AIM-XL-NW25 Gauge is compatible with all of Edwards Active Gauge Controllers and with the appropriate versions of the Active Gauge Displays. Alternatively you can use an independent power supply for the AIM Gauge and you can read the AIM Gauge output signal with a voltmeter or an analogue-to-digital converter.
Applications
All vacuum applications requiring rugged and reliable pressure indication in the range 1 x 10-2 to 1 x 10-9 mbar. Typical processes range from general vacuum through industrial coaters and furnaces to scientific instruments and semicon.
Login to see price! Add to cart - APG series
Edwards APG100-XM NW16 Active Pirani Vacuum Gauge with Calibration Certificate, D0260100C
Edwards APG100 series Active Pirani vacuum gaugesare available in 2 models. The
APG100-XM is the standard model and measures to 10-3 mbar. The APG100-XLC is a
corrosion resistant version with measurement to 10-4 mbar.Both Edwards APG100 gauges feature compact size for easy installation, a linear output, and a replaceable
sensor tube. The new gauges are compatible with all Edwards Vacuum TIC instrument
controllers and other active gauge controllers and displays. They are also CSA, C/US
approved as well as fully RoHS compliant due to their lead-free constructionFeatures and Benefits;
Cable connections and gauge adjustment conveniently located, thereby minimizing the space envelope required for access
Sensor tube can be baked to 150 ºC
Adjustable set-point for simple process control and interlocking
Remote calibration possible
Linear output – 1 volt per decade for easy interface with vacuum control systems
NW16 and NW25 flange options for easy connection to vacuum systems – other flange options on request
LED status indicator shows normal and fault conditionsLogin to see price! Add to cart - E2M 0.7 and 1.5 series
Edwards E2M0.7 Vacuum Pump, Dual Stage, Rotary Vane Pump, Hydrocarbon Elite Z oil, 200-230 VAC, A37141919
The Edwards Vacuum E2M 0.7 pumps are two-stage, direct drive, sliding vane pumps. The E2M0.7 pump is oil-sealed and designed for reliable, long-term operation. The pump is a free-standing unit. The drive is provided through a coupling by a single-phase motor.
The motor of this rotary vane vacuum pump is totally enclosed and is cooled by the motor-cooling fan which directs air along the motor fins. The motors are fitted with a thermal overload device. When the motor is too hot, the thermal overload device switches off the pump. The thermal overload device has an automatic reset; when the motor cools down, the device resets and the motor will restart.
An oil pressure system lubricates the pump shaft bearing surfaces and rotor sealing faces. The pump has an oil distribution valve which prevents discharge of oil to the pump interior (suckback) after the pump stops. The pumping chambers are air-tight, so this arrangement prevents oil suckback unless the gasballast valve is open.
You can inspect the level and condition of oil in the oil box reservoir through a sight-glass. An oil filler-plug is fitted to the top of the oil box. An oil drain-plug is fitted at the bottom of the oil box. The pump has a carrying handle, inlet-port, outlet nozzle and gas-ballast control. The pump is mounted on a steel baseplate on rubber pads.
Edwards Vacuum E2M 0.7 Features:
– Pumping speeds of either 0.7 to 1.5 m3h‑1.
– Industry proven long term reliable performance.
– Free standing, compact design providing flexibility of use.
– Alternate side inlet connection port so that overall installation height can be reduced to minimum when required.
– Low noise, with the E2M0.7 at just 43 dB(A).
– Low energy consumption, with the E2M0.7 at 0.09 kW.
– O ring sealed sight glass allows visual inspection of oil level and condition.
– Gas ballast valve for large water vapour handling capacity.
– Simple installation and operation with no customer wiring.
– Forced air cooling ensures low pump surface temperature.
– Internal ATEX classification of Ex II 3 G c IIB T4.
– Approved EN61010, CSA22.2 and UL61010.Login to see price! Add to cart - E2M 0.7 and 1.5 series
Edwards E2M1.5 Vacuum Pump, Dual Stage, Rotary Vane Pump, Hydrocarbon Elite Z oil, 200-230 VAC, IEC Connector, A37132919
The Edwards Vacuum E2M 1.5 pumps are two-stage, direct drive, sliding vane pumps. The E2M1.5 pump is oil-sealed and designed for reliable, long-term operation. The pump is a free-standing unit. The drive is provided through a coupling by a single-phase motor.
The motor of this rotary vane vacuum pump is totally enclosed and is cooled by the motor-cooling fan which directs air along the motor fins. The motors are fitted with a thermal overload device. When the motor is too hot, the thermal overload device switches off the pump. The thermal overload device has an automatic reset; when the motor cools down, the device resets and the motor will restart.
An oil pressure system lubricates the pump shaft bearing surfaces and rotor sealing faces. The pump has an oil distribution valve which prevents discharge of oil to the pump interior (suckback) after the pump stops. The pumping chambers are air-tight, so this arrangement prevents oil suckback unless the gasballast valve is open.
You can inspect the level and condition of oil in the oil box reservoir through a sight-glass. An oil filler-plug is fitted to the top of the oil box. An oil drain-plug is fitted at the bottom of the oil box. The pump has a carrying handle, inlet-port, outlet nozzle and gas-ballast control. The pump is mounted on a steel baseplate on rubber pads.
Edwards Vacuum E2M 1.5 Features:
– Pumping speeds of either 0.7 to 1.5 m3h‑1.
– Industry proven long term reliable performance.
– Free standing, compact design providing flexibility of use.
– Alternate side inlet connection port so that overall installation height can be reduced to minimum when required.
– Low noise, with the E2M0.7 at just 43 dB(A).
– Low energy consumption, with the E2M0.7 at 0.09 kW.
– O ring sealed sight glass allows visual inspection of oil level and condition.
– Gas ballast valve for large water vapour handling capacity.
– Simple installation and operation with no customer wiring.
– Forced air cooling ensures low pump surface temperature.
– Internal ATEX classification of Ex II 3 G c IIB T4.
– Approved EN61010, CSA22.2 and UL61010.Login to see price! Add to cart - E2M 18 and 28 series
Edwards E2M18 Dual Stage Rotary Vane Pump, Single Phase, 115/200-230 V, 50/60 Hz, A36317984
The Edwards E2M18 Rotary Vane Pump is a vacuum pump that has a pressurized oil system that lubricates the pump shaft bearing surfaces and rotor sealing faces. The pump has an oil distribution valve which prevents discharge of oil to the pump interior (suckback) after the pump stops. The pumping chambers are air-tight, so this arrangement prevents oil suckback unless the gas ballast valve is open.
You can inspect the level and condition of oil in the oil box reservoir through the oil sight-glass. An oil filler-plug is fitted to the top of the oil box. The pump has an oil drain-plug to allow either gravity oil drain or pressure oil drain.
The EM Vacuum Pump Series range of oil‑sealed rotary pumps – renowned for their high ultimate vacuum, rapid pumping speed, quiet operation and ability to handle vapour – have become the industry standard for laboratory and light industrial applications. The pump is a freestanding unit with the drive provided through a flexible coupling by either a single‑phase or three‑phase (four pole) motor.
Edwards E2M 18 Dual Stage Rotary Vane Pump Features:
– The pump is designed for reliable, long‑term operation.
– Thermal overload device prevents overheating (single phase only).
– The drive is provided through a flexible coupling by a single‑phase or three‑phase (four pole) motor.
– The motors are totally enclosed and are cooled by the motor cooling fan.
– Full height O ring sealed oil sight glass for easy checking of oil level and condition.
– Large sight glass and operating oil range.
– IE3 energy efficient 3 phase motor used with E2M28.Login to see price! Add to cart - E2M 18 and 28 series
Edwards E2M18 Dual Stage Rotary Vane Pump, Three Phase, 200-230/380-415 V, 50 Hz or 200-230/460 V, 60 Hz, A36310940
The Edwards E2M18 Rotary Vane Pump is a vacuum pump that has a pressurized oil system that lubricates the pump shaft bearing surfaces and rotor sealing faces. The pump has an oil distribution valve which prevents discharge of oil to the pump interior (suckback) after the pump stops. The pumping chambers are air-tight, so this arrangement prevents oil suckback unless the gas ballast valve is open.
You can inspect the level and condition of oil in the oil box reservoir through the oil sight-glass. An oil filler-plug is fitted to the top of the oil box. The pump has an oil drain-plug to allow either gravity oil drain or pressure oil drain.
The EM Vacuum Pump Series range of oil‑sealed rotary pumps – renowned for their high ultimate vacuum, rapid pumping speed, quiet operation and ability to handle vapour – have become the industry standard for laboratory and light industrial applications. The pump is a freestanding unit with the drive provided through a flexible coupling by either a single‑phase or three‑phase (four pole) motor.
Edwards E2M 18 Dual Stage Rotary Vane Pump Features:
– The pump is designed for reliable, long‑term operation.
– Thermal overload device prevents overheating (single phase only).
– The drive is provided through a flexible coupling by a single‑phase or three‑phase (four pole) motor.
– The motors are totally enclosed and are cooled by the motor cooling fan.
– Full height O ring sealed oil sight glass for easy checking of oil level and condition.
– Large sight glass and operating oil range.
– IE3 energy efficient 3 phase motor used with E2M28.Login to see price! Add to cart - E2M 18 and 28 series
Edwards E2M28 Dual Stage Rotary Vane Pump, Single Phase, 115/200-230 V, 50/60 Hz, A37317984
The E2M28 Rotary Vane Pump is a two-stage, direct drive, sliding vane pump. The pump is oil-sealed and designed for reliable, long-term operation in both laboratory and industrial environments. The pump is a free-standing unit. The drive is provided through a flexible coupling by a single-phase or three-phase (four pole) motor.
The motors are totally enclosed and are cooled by the motor-cooling fan which directs air along the motor fins.
The single-phase motors have a thermal overload device. When the motor is too hot, the thermal overload device switches off the pump. The thermal overload device has an automatic reset; when the motor cools down, the device resets and the motor will restart. The single phase motors have an on/off switch.
An oil pressure system lubricates the pump shaft bearing surfaces and rotor sealing faces. The pump has an oil distribution valve which prevents discharge of oil to the pump interior (suckback) after the pump stops. The pumping chambers are air-tight, so this arrangement prevents air suckback unless the gas-ballast valve is open.
You can inspect the level and condition of oil in the oil box reservoir through the oil sight-glass. An oil filler-plug is fitted to the top of the oil box. The pump has an oil drain-plug to allow gravity oil drain.
The pump has an inlet-port, outlet nozzle and gas-ballast control. The pump is mounted on an aluminum alloy baseplate on rubber pads.
Edwards E2M28 Rotary Vane Vacuum Pump Features:
– The pump is designed for reliable, long‑term operation.
– Thermal overload device prevents overheating (single phase only).
– The drive is provided through a flexible coupling by a single‑phase or three‑phase (four pole) motor.
– The motors are totally enclosed and are cooled by the motor cooling fan.
– Full height O ring sealed oil sight glass for easy checking of oil level and condition.
– Large sight glass and operating oil range.
– IE3 energy efficient 3 phase motor used with E2M28.Login to see price! Add to cart - E2M 18 and 28 series
Edwards E2M28 Rotary Vane Vacuum Pump, Hydrocarbon Oil, Dual Stage, 200-220/380-415 V, Three Phase, 50Hz, A37310940
The E2M28 Rotary Vane Pump is a two-stage, direct drive, sliding vane pump. The pump is oil-sealed and designed for reliable, long-term operation in both laboratory and industrial environments. The pump is a free-standing unit. The drive is provided through a flexible coupling by a single-phase or three-phase (four pole) motor.
The motors are totally enclosed and are cooled by the motor-cooling fan which directs air along the motor fins.
The single-phase motors have a thermal overload device. When the motor is too hot, the thermal overload device switches off the pump. The thermal overload device has an automatic reset; when the motor cools down, the device resets and the motor will restart. The single phase motors have an on/off switch.
An oil pressure system lubricates the pump shaft bearing surfaces and rotor sealing faces. The pump has an oil distribution valve which prevents discharge of oil to the pump interior (suckback) after the pump stops. The pumping chambers are air-tight, so this arrangement prevents air suckback unless the gas-ballast valve is open.
You can inspect the level and condition of oil in the oil box reservoir through the oil sight-glass. An oil filler-plug is fitted to the top of the oil box. The pump has an oil drain-plug to allow gravity oil drain.
The pump has an inlet-port, outlet nozzle and gas-ballast control. The pump is mounted on an aluminum alloy baseplate on rubber pads.
Edwards E2M28 Rotary Vane Vacuum Pump Features:
– The pump is designed for reliable, long‑term operation.
– Thermal overload device prevents overheating (single phase only).
– The drive is provided through a flexible coupling by a single‑phase or three‑phase (four pole) motor.
– The motors are totally enclosed and are cooled by the motor cooling fan.
– Full height O ring sealed oil sight glass for easy checking of oil level and condition.
– Large sight glass and operating oil range.
– IE3 energy efficient 3 phase motor used with E2M28.Login to see price! Add to cart - New Turbo Pump Controllers
Edwards EXDC80 Turbo Pump Controller, 24V, 93W, D39645000
The Edwards EXDC80 Turbo Pump Controller generates the control signals necessary to operate an EXT pump and its accessories.
The EXDC has no manual controls and can only be operated through the logic interface. To operate the EXT pump, you must therefore connect the EXDC to your own control equipment and electrical supply.
This Controller is designed for the following Mass Spectrometer Turbo Pumps:
- Edwards EXT 70 Turbo Pump
- Edwards EXT 70H Turbo Pump
- Edwards EXT 250 Turbo Pump
- Edwards EXT 255H Turbo Pump
Login to see price! Add to cart